Inject HV 1000 (High Viscosity Injection Resin) 3 gal Kit by: Johnson

Inject HV 1000 (High Viscosity Injection Resin) 3 gal Kit Inject-HV1000 3gal Inject HV 1000 Regular Set High Viscosity Epoxy Resin [Johnson Group Online Inc.]	CAD $290.00
	Availability: This item is not stocked. Call for Availability.

Inject HV 1000 (High Viscosity Injection Resin) 3 gal Kit

Epoxy Injection Resin
(High Viscosity)

3 gal Kits

INJECT HV 1000 is a high viscosity 2 component moisture insensitive 100% solid structural epoxy adhesive for pressure grouting of non-moving cracks. This product has been designed to prevent the leaking of epoxy resin out of injected cracks before it can cure. As this is a very common problem that has caused countless projects to fail, we offer this product which will remain where injected. INJECT HV 1000 can also be mixed with aggregate to make a high strength epoxy repair mortar for use as a grout for setting anchor bolts, dowels, or rebar into concrete. This formulation is designed for use with dual component pumps although skilled installers may be able to use single component systems effectively.

Epoxy injection on CN Rail bridge wing wall.

PHYSICAL PROPERTIES

UNCURED RESIN                              PART A                                           PART B (CATALYST)

APPEARANCE                              CLEAR LIQUID                                PALE AMBER LIQUID
VISCOSITY  MIXED                        1000 cps @ 25ºC (77ºF)                                                                    ASTM D - 1638
SOLIDS                                          100%                                                 100%                                            ASTM D - 1010
SPECIFIC GRAVITY                     1.10                                                    1.03                                              ASTM D - 1638
FLASH POINT                                >170ºC (338ºF)                               >155ºC (311ºF)                          ASTM D - 93
WEIGHT                                          4.08 kg (9 lbs)                                 3.62 kg (8 lbs)
MIX RATIO                                       100                                                    50
GEL TIME                                        ................................Approx. 20 - 45 MINUTES........................................

CURED FILM

HARDNESS SHORE                                                          78D                                                                   ASTM D - 2240
TENSILE STRENGTH                                                        52 mpa                                                             ASTM D - 412
FLEXURAL STRENGTH                                                    36 mpa                                                             ASTM D - 790
COMPRESSIVE STRENGTH                                            52 mpa                                                             ASTM D - 695
BOND ELONGATION                                                         4.5 mpa (48 hrs)                                             ASTM D - 321
ELONGATION                                                                      45%                                                                   ASTM D - 638
WATER ABSORPTION                                                       0.25% (24 hrs)                                                ASTM D - 570

Packaging:    This product is INJECT-HV 1000. It is packaged in a 3 gal (11.36 liter) kit. (2:1 mix ratio) SKU# inject-HV1000.
This product is also available in a 15 gal (56.78 liter) kit.

Mixing:     If using single component pumps (not recommended), mix only the amount of material that can be used before the pot life expires 20 to 45 minutes depending on temperature. Mix two (2) parts of resin (Part A) to (1) one part of hardener (Part B).
ALWAYS MIX THOROUGHLY!
IMPROPER MIXING IS THE GREATEST CAUSE OF EPOXY SYSTEMS FAILURE. Be sure to thoroughly scrape sides of mixing container to get all unblended resin.
For dual pumps set metering equipment for 2:1 BY VOLUME OF A:B INJECT-HV 1000 and use a static mixing attachment.

Injecting:     Unless the crack is wide open and will not resist the injected INJECT-HV 1000 we recommend using high pressure injection methods using the Hammer-In Plastic Packers or in poor concrete, the Mechanical (Metal) Packers to achive pressures which will sufficiently fill the entire crack.

Single Component Pump Caution:     Warm or hot weather conditions will greatly increase the gel time of the standard mix of INJECT-HV 1000. Keep the batch cool. Viscosity will increase as time passes making it harder to inject the product requiring higher pressures. Large mixed batches will begin to generate their own heat as the gel pot life progresses causing a flash of the product in the pump if using single component pumps (not recommended). When this happens the product may be hot enough to burn skin and boil water.

Safe Single Component Pump Use:     The use of our Slow Set Epoxy product INJECT LVI 300 SS will allow the use of single component pumps. Please note the viscosity differences before ordering.

Limitations:
Minimum substrate temperature is 5°C (40°F)
Thinning with solvents will prevent proper cure.
Minimum age of concrete must be 5-7 days, depending on curing and drying conditions, for mortar.

Cleanup:     Uncured material can be removed with xylene or another approved solvent. Cured material can only be removed mechanically. Use absorbent material to collect spills and drips. Flush area with water. Dispose of in accordance with local, provincial, state and federal disposal regulations.

Safety:     Always wear protective equipment when working with epoxies and their additives. Wear approved safety glasses or goggles. A face shield is advisable when working with materials under pressure. Rubber gloves will protect & prevent adhesion of product to hands. Keep spectators back. It is advisable to always keep one hand on the coupler while injecting to minimize random spraying if the coupler pops off or there is a blowout.

     EYE CONTACT: Flush immediately with water for at least 15 minutes.
                             Contact physician immediately.
     RESPIRATORY CONTACT: Remove person to fresh air.
     SKIN CONTACT: Remove any contaminated clothing. Remove
                              epoxy immediately with a dry cloth or paper towel. Solvents
                              should not be used as they carry the irritant into the skin. Wash
                              skin thoroughly with soap and water.

History:     INJECT-HV 1000 is one in a family of very high quality injection products that have been used extensively since 1993. Their designs have been based on extensive industry experience and exacting standards.

The INJECT-HV 1000 product is made in Ontario, Canada and exclusively supplied to Johnson Group Online by Quality Restoration Products, QRP Inc. for internet sales at http://www.leak-proof.com/catalog. Our internationally renowned manufacturer produces high quality products for QRP Inc. under exclusive agreement.

Warranty:   All information and statements are intended for persons having the required skill and know-how and do not relieve the user from verifying the suitability of the information and statements given for a specific purpose prior to use. The information, and in particular, the recommendations relating to the application and end-use of our products, are given in good faith based on Johnson Group Online and its manufacturers current knowledge and experience of the products when properly stored, handled and applied under normal conditions, within their shelf life, but accuracy and completeness of said information is not guaranteed and are not to be construed as a warranty either expressed or implied. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or of ﬁtness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any recommendations, or from any other advice offered. Users should always refer to the most recent issue of the Technical Data Sheet and the MSDS for the product concerned, copies of which will be supplied on request or can be accessed in the internet under www.leak-proof.com/catalog.

Neither seller nor manufacturer shall be liable to buyer or any third person for any injury, loss or damage directly or indirectly resulting from use or inability to use this product. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery.

Johnson Group Online warrants its products to be manufactured free of defects and will replace or, at our option, refund the purchase price of any materials proven to be defective. Seller’s and manufacturer’s sole responsibility shall be to replace that portion of the product of this manufacturer which proves to be defective. This limited warranty is in lieu of any other guarantee, expressed or implied, including warranties of merchantability or fitness for a particular purpose. In no event will Johnson Group Online be liable for incidental or consequential damages nor shall liability, if any, extend beyond the purchase price of the material.

KEEP ALL PRODUCTS
OUT OF REACH OF CHILDREN

FOR INDUSTRIAL USE ONLY

We know you will be impressed by our products.
We are!

Johnson Group Online
761-D Bayview Drive, Barrie, Ontario, Canada L4N 9A5
Office (705) 728-3476, Fax (705)-728-3305
Email: johnsongroup@leak-proof.com
www.leak-proof.com

This product was added to our catalog on Tuesday 06 June, 2006.

We won't be beaten on price!
Click here to PriceMatch this product.

Quantity:

Click Here for a Printer Friendly Page