Fast curing epoxy adhesive gel
DESCRIPTION
CIPADITE ® GEL 15 is a 100% solids two component, high modulus high strength, moisture insensitive fast setting epoxy adhesive gel.
WHERE TO USE
CIPADITE ® GEL 15 is recommended for bonding new concrete to old concrete, repairing spalled, scaled and cracked concrete, structural bonding adhesive for vertical dowels and anchors, bonding of precast concrete units, steel plates or other metal sections to concrete and crack sealing for epoxy injection work.
BENEFITS
• excellent adhesion properties.
• very easy to mix and apply
• cures under cool, damp conditions
• rapid development of hardness and mechanical strengths
• moisture insensitive during the cure
• high shear and tensile strength
PROPERTIES (Tested @ 23 ° C (74 ° F) Mix Ratio, by Volume . . . . . . . . . . . 2 parts A:1 part B
Viscosity (Mixed) . . . . . . . . . . . . . . . thixotropic paste
Pot-Life 100g . . . . . . . . . . . . . . . . . . . . . . 15 minutes
Tensile Strength . . . . . . . . . . . . . . 28 MPa (4000 psi)
Tensile Elongation . . . . . . . . . . . . . . . . . . . . . . . . 2 %
Compressive Strength . . . . . . . . . . 60 MPa (8700 psi)
The above information is representative of actual production runs. Independent test results may vary from the above by approximately ± 10 %.
APPLICATION
SURFACE PREPARATION
Concrete should be sound and free from dust, loose particles and all foreign contamination. All concrete should be chemically cleaned or mechanically scarified for best results. New concrete should be cured 30 days and any surface laitance or curing compound must be removed. For anchorages, core holes should be scored, free of all dust and mud and dry for maximum bond. Holes should be of a minimum of 4 mm greater in diameter than the anchor. Anchorages must be free of all rust, scale and mill oil. A solvent wash is recommended for all anchorages prior to installation. Fill holes to slight excess required, insert anchorage and rotate slowly to assure that no air pockets remain. Where sandblasting is not practical, the surface should be degreased and mechanically abraded to reveal continuous bright metal. MIXING
Premix each component separately before using. Combine 2 parts (by volume) of Part A with 1 part (by volume) of Part B. Mix with a low speed drill. Thoroughly blend the material until an even consistency is achieved, periodically scraping down sides and bottom of container. Apply as soon as possible as pot life is limited.
LIMITATIONS
CIPADITE ® Gel 15 is not recommended for:
COVERAGE
Bonding Adhesive 2.0 m²/L (81.5 ft²/U.S. gal)(smooth surface).
PACKAGING
3.79L (1 U.S. gal)
18.9L (5 U.S gal.)
CLEAN UP
Clean all equipment with CPD ® Xylol before epoxy hardens. CPD ® Xylol is a flammable solvent. Read the Material Safety Data Sheet before using.
STORAGE
Store in a heated warehouse. Storage at temperatures below 4.5°C (40°F) may cause the resin to crystallize.
SHELF LIFE
Two years if kept in original unopened containers under normal warehouse conditions.
SAFETY PRECAUTIONS
Consult Material Safety Data Sheet ( M.S.D.S.) for specific instructions. M.S.D.S. # 306, 306A WARRANTY
The recommendations made and the information herein is based on our own and independent laboratory experience, and is believed to be accurate under controlled conditions. However, no warranty or guarantee of accuracy is made because we cannot cover every possible application of product nor anticipate every variation encountered in weather conditions, job-conditions, methods used and types of surfaces on which the product is applied. The users shall make their own tests to determine the suitability of such products for any particular purpose. CPD® makes no warranties with respect to this product, expressed or implied, without limitation, the implied warranties of merchantability or fitness for a particular purpose. CPD®’s liability shall be limited in all events to supplying sufficient product to re-treat and/or repair the specific area to which CPD® product has been applied. CPD® reserves the right to have the true cause of any difficulty determined by accepted test methods. CPD® shall have no other liability, including liability for incidental, consequential or resultant damages, however caused, whether due to breach of warranty, negligence, or strict liability.
THIS WARRANTY MAY NOT BE MODIFIED OR EXTENDED BY REPRESENTATIVES OF CPD® , ITS DISTRIBUTORS OR DEALERS.
Pressure Grouting 
